SHOPPING CART
0
items -
$0.00
PIC18F2525-I/SP (PDIP/ SOIC)
$8.90
Tax excluded
PIC18F2525-I/SP (PDIP-28)
Pin Diagram:
Features & Specification:
CPU
- Up to 10 MIPS performance
- C compiler optimized RISC architecture
- 8 x 8 Single Cycle Hardware Multiply
System
- Internal oscillator support 31 kHz to 8 MHz
- Fail-Safe Clock Monitor – allows safe shutdown if clock fails
- Watchdog Timer with separate RC oscillator
- Wide operating Voltage range; 2.0V to 5.5V
nanoWatt Power Managed Modes
- Run, Idle and Sleep modes
- Idle mode currents down to 5.8uA typical
- Sleep mode currents down to 0.1uA typical
Analog Features
- 10-bit ADC, 10 channels, 100K samples per second
- Programmable Low Voltage Detection Module
- Programmable Brown-out Reset module
- Two Analog comparators with input multiplexing
Peripherals
- Master Synchronous Serial Port supports SPI ™ and I2C™ Master and Slave Mode
- EUSART module including LIN bus support
- Four Timer Modules
- Up to 2 PWM outputs
- Up to 2 Capture / Compare
Download:
- PIC18F2525 Data Sheet: Link
FEATURED PRODUCT
You might also like
Please choose the latest iCP02v2 USB PIC programmer model
For bulk order on this model, please contact us. iCP01v2 USB ICSP PIC programmer used for programming the Microchip PIC10F, PIC12F, PIC16F, PIC18F, dsPIC30 family with PICkit 2 and MPLAB IDE software.
USB PIC Programmer Set allows users to program their hex code into Microchip Flash PIC MCU by using In-Circuit Programming (ICSP) method or Off-Board Programming (Adapter) method with MPLAB and PICKit 2 software.
NEW iCP02v2 is used for programming the Microchip PIC10F, PIC12F, PIC16F, PIC18F, PIC24F, dsPIC30, dsPIC33 family and serial EEPROM 11LCXX, 24LCXX, 25LCXX, 93LCXX and KEELOQ HCSXX with PICkit 2 and MPLAB IDE software.
iCA03 allows users to program 5V or 3.3V Flash PIC MCU by using In-Circuit Programming (ICSP) method or Off-Board Programming (Adapter) method.
Customers who bought this product also bought:
This PIC16F628A is a 18-pin Flash-based 8-bit microcontroller with EEPROM, comparator, Caputure/Compare/PWM and USART peripheral.
This PIC12F1840 is a 8-pin Flash-based 8-bit microcontroller with 5+1 I/O Pins, 4x 10-bit ADC, 1x comparator, 1x ECCP, 1x A/E/USART, 1x MSSP(SPI/I2C), 4x Cap Sense and 256 bytes of EEPROM data memory.
This PIC16F722 is a 28-pin Flash-based 8-bit microcontroller with Extreme Low Power MCUs featuring nanoWatt XLP(TM) Technology.
This PIC12F629 is a 8-pin Flash-based 8-bit microcontroller with 5+1 I/O Pins, 1 channel comparator and 128 bytes of EEPROM data memory.
This PIC18F2525 is a 28-pin Flash-based 48 KB microcontroller with 10x 10-bit A/D Converter, 2x comparators, UART, A/E/USART and SPI, I2C1-MSSP (SPI/I2C) peripherals.